Call a Specialist Today! 844-294-0778

Palo Alto Networks M-200 Management Appliance
16TB RAID storage (4 8TB RAID certified drives preinstalled)

Palo Alto Networks M-200 Management Appliance

Palo Alto Networks Products
M-200 Management Appliance
Palo Alto Networks M-200 16TB RAID storage (4 8TB RAID certified drives preinstalled). Rack mount rails included.
#PAN-M-200
Request a Quote for Pricing!

Click here to jump to more pricing!

Overview:

The Palo Alto Networks® M-200 and M-600 appliances are multi-function appliances that you can configure to function in Panorama™ Management mode, Panorama Management-only mode, Panorama Log Collector mode, or PAN-DB Private Cloud mode.

First Supported Software Release: Panorama 8.1

Front Panel:

Item
Component
Description
1
System drive
240GB solid-state drive (SSD) used to store the operating system files and system logs.
2
Unique Identification (UID) button
Use the UID feature to help you locate the appliance when you move from the front to the back of the equipment rack where the appliance is installed. When you push the UID button to enable the UID feature, both the front-panel System information LED and the back-panel UID LED illuminate bright blue to help you locate the appliance when you move between opposite sides of the equipment rack. Push the UID button again to deactivate these LEDs.
3
System information (overheat and UID) LED
  • Solid red—An overheat condition occurred.
  • Blinking red at the rate of one blink per second (1Hz)—A fan failure occurred.
  • Blinking red at the rate of four blinks per second (.25Hz)—One of the two power supplies is not providing power to the appliance (possibly because a power supply failed or because there is no power source connected to the power supply).
  • Solid blue—The UID feature is activated (see the UID button description).
4
Network activity LEDs
Blinking green indicates network activity.
5
Hard-disk drive (HDD) LED
Blinking yellow indicates IDE channel activity (SAS/SATA drive) on the front log drives.
6
Power LED
Solid green indicates that the appliance is powered on.
7
Reset button
Press this button to reboot the appliance.
8
Power button
Press this button to power on or power off the appliance. Powering off the appliance with this button puts the appliance in standby power mode. To completely power off the appliance, you must disconnect the AC power cords from both power supplies.
9
Hard-disk drives (HDDs)
Disk drive bays and HDDs used for log storage. By default, the M-200 ships with four HDDs installed in drive bays A1/A2 and B1/B2. Each pair of drives are in a RAID 1 configuration (A1-A2 is a RAID 1 pair and B1-B2 is a RAID 1 pair).
For details on storage capacity, refer to the Panorama Datasheet .
10
Hard-disk drive (HDD) LEDs
Status LEDs—two for each log drive:
  • Top LED—Flashing blue indicates drive activity.
  • Bottom LED—Solid red indicates a log drive failure.

Back Panel:


Item
Component
Description
1
Power supplies
Use the AC power supply inputs to connect power to the appliance. The second power supply is for redundancy.
2
Ethernet ports
Four RJ-45 10Mbps/100Mbps/1000Mbps Ethernet ports. While facing the back of the appliance, the ports are labeled as follows:
The port labels are located on top of the appliance.
  • Upper left—Management (MGT) port used for managing the appliance and for data traffic.
  • Upper right—Ethernet1/1
  • Lower left—Ethernet1/2
  • Lower right—Ethernet1/3
For information on configuring these ports, refer to the Panorama™ Administrator’s Guide on the Technical Documentation Portal for the release version running on your appliance. If the appliance is in PAN-DB mode, refer to the appropriate release-specific PAN-OS® Administrators Guide.
3
USB ports
Not used.
4
IPMI port
Not used.
5
Console port
Use this port to connect a management computer to the appliance using a 9-pin serial cable and terminal emulation software.
The console connection provides access to appliance boot messages, the Maintenance Recovery Tool (MRT), and the command line interface (CLI).
If your management computer does not have a serial port, use a USB-to-serial converter.
Use the following settings to configure your terminal emulation software to connect to the console port:
  • Data rate: 9600
  • Data bits: 8
  • Parity: None
  • Stop bits: 1
  • Flow control: None
6
Unique Identification (UID) LED
UID LED that illuminates bright blue when you push the UID button on the front of the appliance.
For information on using the UID feature, see the UID button description for the M-200 Appliance Front Panel .

Documentation:

Download the Palo Alto Networks M-200 (PDF).

Pricing Notes:

Palo Alto Networks Products
M-200 Management Appliance
Palo Alto Networks M-200 16TB RAID storage (4 8TB RAID certified drives preinstalled). Rack mount rails included.
#PAN-M-200
Request a Quote for Pricing!